外圆磨床-通用KELLENBERGER
Kel-Varia UR225-1500 FANUC
外圆磨床-通用
KELLENBERGER
Kel-Varia UR225-1500 FANUC
出厂年份
2002
状况
二手
位置
Kirchheim unter Teck 

基本数据
价格和位置
- 位置:
- 73230 Kirchheim

拨打
优惠详情
- 广告编号:
- A17404443
- 参考编号:
- 1056-M24Vari
- 更新:
- 最近更新时间为 10.11.2026
描述
grinding diameter 450 mm
grinding length 1500 mm
centre height 225 mm
Control FAGOR
Hedpjuxfu Nsfx Al Renw
NEW: New CNC Control FANUC with Blue Solution
EQUIPEMENT
- T1: grinding wheel diameter 500 mm
- T2: grinding wheel diameter 400 mm
- T6: HF Fischer spindle MFV or MFZ 1224/1242/1260
- T7: HF Fischer spindle MFV or MFZ 1224/1242/1260
- Marposs tool measurement
- active longitudinal positioning
- Elaso GAP-control on T1 and T2
contactless integrated in the control surface
- Elaso GAP internal grinding with fluid sensor for T6 and T7
- semi-automatic balancing by Elaso
integrated in the control surface for T1/T2
- tailstock hydraulic with fine adjustment +/- 150 microns
- dresser on workpiece spindle side table mounted
- dresser on tailstock side table mounted
- dresser on upper table
- new service- and userfriendly housing
SPECIAL EQUPEMENT:
Workhead with direct drive
- strongly recommended for
non-circular grinding
- workpiece weight flying max. 75kg
- workpiece weight between centres 150kg
- water-cooled
B-axis with direct drive
- center height 225 mm
- extremely torsionally stiff
- highly accurate positioning
- resolution °
- water-cooled
Hydrostatic ball screw - x-axis
- wear-free, as there is no contact during operation
- no loss of precision, even during long-term use at full load and
maximum speed
- no friction at low speeds
- no friction force backlash when the direction of rotation changes
- translates even the smallest rotational movements
- no stick-slip effect even at low speeds
- no fluctuations in frictional torque due to ball circulation
- higher axial stiffness compared to ball screws
- significant improvement in damping, resulting in better workpiece surface
finish and tool life
- no oscillations due to ball circulation
- also suitable for high speeds and accelerations
- cost-effective alternative to the linear motor with greater precision and
significantly lower heat generation
- significantly less power dissipation and, as a result, no problems with swarf
on permanent magnets
New hydraulic unit
- optimized temperature control (chiller)
- Energy-saving
Only one pump controlled by VFD
- Pressure monitoring
- monitoring of the hydrostatic oil for
water content.
(Damage to the bellows is recognised and detected prematurely)
-fine adjustment +/- 150 microns
Paper belt filter
375l – alternative 480l
Grinding mist extraction system – emulsion
MECHANICAL OVERHAUL
-complete machine according to Kellenberger protocoll
-new painting
ELECTRICAL OVERHAUL
- new modern Fagor CNC with BEMA HMI
- new electric cabinet
- new digital drive technology
- replacement of all electrical cables, switches etc.
- new absolute external scales in x- and z-axis
- new absolute encoder (B-axis)
Grinding software BEMA-Standard:
- workpiece zeroing
- grinding wheel zeroing
- dressing diamond measuring
- corrections
- external and internal surface grinding
- external and internal angle grinding
(turning of the b-axis, dressing with straight wheel)
- external and internal radius grinding (radius dressed on wheel)
- semi-automatic traverse grinding
- workpiece zeroing
- 2 dressing diamonds
- 1 dressing blade
- dressing roll
- 3 flat dresser
- corrections
- Z-position measurement
- GAP control
Optional grinding cycles at no extra charge:
Profile plunge grinding:
- external and interna...
grinding length 1500 mm
centre height 225 mm
Control FAGOR
Hedpjuxfu Nsfx Al Renw
NEW: New CNC Control FANUC with Blue Solution
EQUIPEMENT
- T1: grinding wheel diameter 500 mm
- T2: grinding wheel diameter 400 mm
- T6: HF Fischer spindle MFV or MFZ 1224/1242/1260
- T7: HF Fischer spindle MFV or MFZ 1224/1242/1260
- Marposs tool measurement
- active longitudinal positioning
- Elaso GAP-control on T1 and T2
contactless integrated in the control surface
- Elaso GAP internal grinding with fluid sensor for T6 and T7
- semi-automatic balancing by Elaso
integrated in the control surface for T1/T2
- tailstock hydraulic with fine adjustment +/- 150 microns
- dresser on workpiece spindle side table mounted
- dresser on tailstock side table mounted
- dresser on upper table
- new service- and userfriendly housing
SPECIAL EQUPEMENT:
Workhead with direct drive
- strongly recommended for
non-circular grinding
- workpiece weight flying max. 75kg
- workpiece weight between centres 150kg
- water-cooled
B-axis with direct drive
- center height 225 mm
- extremely torsionally stiff
- highly accurate positioning
- resolution °
- water-cooled
Hydrostatic ball screw - x-axis
- wear-free, as there is no contact during operation
- no loss of precision, even during long-term use at full load and
maximum speed
- no friction at low speeds
- no friction force backlash when the direction of rotation changes
- translates even the smallest rotational movements
- no stick-slip effect even at low speeds
- no fluctuations in frictional torque due to ball circulation
- higher axial stiffness compared to ball screws
- significant improvement in damping, resulting in better workpiece surface
finish and tool life
- no oscillations due to ball circulation
- also suitable for high speeds and accelerations
- cost-effective alternative to the linear motor with greater precision and
significantly lower heat generation
- significantly less power dissipation and, as a result, no problems with swarf
on permanent magnets
New hydraulic unit
- optimized temperature control (chiller)
- Energy-saving
Only one pump controlled by VFD
- Pressure monitoring
- monitoring of the hydrostatic oil for
water content.
(Damage to the bellows is recognised and detected prematurely)
-fine adjustment +/- 150 microns
Paper belt filter
375l – alternative 480l
Grinding mist extraction system – emulsion
MECHANICAL OVERHAUL
-complete machine according to Kellenberger protocoll
-new painting
ELECTRICAL OVERHAUL
- new modern Fagor CNC with BEMA HMI
- new electric cabinet
- new digital drive technology
- replacement of all electrical cables, switches etc.
- new absolute external scales in x- and z-axis
- new absolute encoder (B-axis)
Grinding software BEMA-Standard:
- workpiece zeroing
- grinding wheel zeroing
- dressing diamond measuring
- corrections
- external and internal surface grinding
- external and internal angle grinding
(turning of the b-axis, dressing with straight wheel)
- external and internal radius grinding (radius dressed on wheel)
- semi-automatic traverse grinding
- workpiece zeroing
- 2 dressing diamonds
- 1 dressing blade
- dressing roll
- 3 flat dresser
- corrections
- Z-position measurement
- GAP control
Optional grinding cycles at no extra charge:
Profile plunge grinding:
- external and interna...
供應商
注意: 免费注册或登录,以获取所有信息。
注册于: 2002
47 在线广告
发送询价
电话 & 传真
+49 7021 ... 广告
这些广告您可能也感兴趣。
成功
您的消息已发送。
小广告
Dortmund
7,394 km
直动力刀架
NACKE + WTOVDI 50
NACKE + WTOVDI 50
成功
您的消息已发送。
小广告
德国
7,232 km
数控平面研磨机
JungJE600
JungJE600
成功
您的消息已发送。
小广告
Offenbach an der Queich
7,476 km
切割和定心机
UMA - SZMSZM 100/1000
UMA - SZMSZM 100/1000
成功
您的消息已发送。
小广告
Mönchengladbach
7,481 km
三坐标测量机
MitutoyoCrysta Apex C776
MitutoyoCrysta Apex C776
成功
您的消息已发送。
小广告
Ybbs an der Donau
7,077 km
傅立叶变换红外光谱仪 - NICOLET IS20
ThermoFisher ScientificNICOLET IS20
ThermoFisher ScientificNICOLET IS20
成功
您的消息已发送。
小广告
Contamine-sur-Arve
7,768 km
数控多轴自动车床
INDEXMS32C
INDEXMS32C
成功
您的消息已发送。
小广告
Hövelhof
7,306 km
麻花钻和埋头孔磨削
Rohde&Doerrenberg (May)SS 40U
Rohde&Doerrenberg (May)SS 40U
成功
您的消息已发送。
小广告
Brügg
7,651 km
数控外圆磨床
KELLENBERGERKEL-VARIA R175 x 1500
KELLENBERGERKEL-VARIA R175 x 1500
成功
您的消息已发送。
小广告
德国
7,492 km
Schaudt Mikrosa SASL 125
Schaudt MikrosaSASL 125
Schaudt MikrosaSASL 125
成功
您的消息已发送。
小广告
Lontzen
7,534 km
圆柱磨床
TosBUB E 50/2000
TosBUB E 50/2000
您的广告已成功删除
发生错误


















































































